Page Title

POLE SHAFT: The pole shafts shall= be extruded from all new 6000 series alloy aluminum tubing. The roun= d straight shafts shall be longitudinally polished, resulting in a high qua= lity brushed finish. After finishing, each pole shall be fully wrappe= d with neutral PH crinkle/kraft paper for protection in shipment. The= shaft is uniformly round in cross section and shall comply with metallurgi= cal and mechanical properties set forth in the Aluminum Association Standar= ds.

GENERAL SPECIFICATIONS

ANCHOR BASE: The anchor base (base= plate) is fabricated from mold casting from A356 alloy aluminum. The= shaft shall be inserted into the base casting and joined by a continuous c= ircumferentially weld at the outside top and inside bottom of the anchor ba= se. The base is provided with a slotted anchor bolt opening that enab= les a range of bolt circles to be utilized. The pole chart informatio= n lists bolt circle ranges for each pole type.

ANCHOR BOLTS: <= span lang=3Den-US style=3D'font-family:"Arial Narrow";language:en-US'>The anch= or bolts are fabricated from carbon steel bar conforming to AASHTO M314 Gra= de-55 or ASTM F1 554 Grade-55 that meets or exceeds a minimum strength of 5= 0,000 psi. Bolts have an “L” bend on one end and are galv= anized a minimum of 12” on the threaded end. Four anchor bolts = are provided per pole. Each anchor bolt is furnished with (2) each - = regular hex nuts and flat washers, unless otherwise specified.

HANDHOLE: The reinforcing handh= ole has a nominal rectangular 2-1/2” X 4-1/2” inside opening in= the pole shaft. It is = ; provided with a cover plate, attachment bar, and machine screw. The= handhole is welded in the pole shaft and is located = ; 16 inches abo= ve base plate and on the same side with respect to the luminaire arm. = For two arms with 180° arrange= ment, handhole is located on the side of the pole with no luminaire arm.

ELECTRICAL GROUND: Grounding bolt is wel= ded inside the pole shaft on the opposite side of the handhole and includes= 3/8”-16 UNC hex head bolt and nut.

BASE COVER: The stan= dard two-piece base cover completely conceals the entire base plate and anc= horage.

POLE TOP CAP: A removable top cap i= s provided and is used in conjunction with drilled pole shafts for accommod= ation of a direct mounted luminaire attachment.

POLE TOP TENON (OPTIONAL): Pole top= tenons are fabricated from all new 6000 series alloy extruded aluminum tub= ing. A pole top plate and tenon is circumferentially welded to the to= p of the pole shaft. This plate provides an internal weather resistan= t wire way into the pole top tenon. Standard size is 2-7/8” O.D= . X 5-1/2” long aluminum tubing.

STANDARD FINISH: Poles are finished wi= th electrostatically applied and thermally cured TGIC polyester powdercoat.= For other coating systems beyond the standard finish, please consult= factory.

DESIGN: The poles as charted = are designed to withstand dead loads and theoretical dynamic loads develope= d by variable wind speeds with an appropriate gust factor under the followi= ng conditions:

The wind velocities are based on 10 mph increments from 70 mph to 110 mp= h. Poles standards to be located in areas of known abnormal condition= s require special consideration. For example, coastal areas, airports= , and areas of special winds such as canyons and mountains.

Standards are designed for ground mounted applications. Poles moun= ted above grade or on structures (such as buildings and bridges) may also n= ecessitate special consideration.

Height correction factors and drag coefficients are applied to the entir= e structure. An appropriate safety factor is maintained based on the = minimum yield strength of the material incorporated in the standard. = However, for any scope beyond the standard application, please consult gove= rning agency and qualified professional.

CAUTION:

Factory supplied template must be used when setting anchor bolts. = Newport Lighting will not honor any claim for incorrect anchorage placement= from failure to use factory supplied templates.

The standard is intended as a general guideline only. The customer= is solely responsible for proper selection of pole, = ; luminai= re, accessory and foundation under the given site conditions and intended u= sage. Newport Lighting assumes no = responsibility for such proper analysis or product selec= tions.

ORDER GUIDE

Note: Mounting height is the vertical distance from the base of the light= ing pole to the center of the luminaire arm at the point of luminaires̵= 7; attachment. Maximum weight and EPA values are determined by analyz= ing stress from two wind directions, across flats and across points. = The design information is intended as a general guideline only. Consu= lt governing agency and qualified professional.

TYPICAL INSTALLATION

<= ![endif]>

Ground Bolt

Newport Lighting recommends consulting a certified local engineer where = the poles are to be installed.

When products are used on an existing foundation or on other structures,= the customer assumes all responsibility for the entire structural integrit= y of the existing foundation, anchorage, structures, equipment, and all the= consequences arising therefrom.

Poles should never be erected without the luminaire installed and non-sh= rink grout must be placed under the entire base after installation. A= ll warranty is voided if not properly installed.

Use of banners or other appendages can severely affect the loading of a = pole. In addition, pole standards subject to vibration, oscillations,= and other fatigue stresses are not covered by the warranty.

Please refer to the General Specifications Design and Caution section of= Newport Lighting Pole-Straight Round Aluminum (page 1) for additional info= rmation prior to selection, purchase, and placement of the pole standards.<= /span>

WARNING

REV. 050109

8629 Bradley Avenue

Sun Valley, CA 91352

Tel (818)771-0552

Fax (818)771-0561

Manufacturer of Architectural Lighting Prod= ucts

www.newportltg.com

Due to our continuing product improvement and refinement,= Newport Lighting reserves the right to change, modify and/or alter any spe= cifications contained herein without prior notice.

DIMENSIONS / WEIGHT ANCHOR BOLTS / BOLT PATTERN	ALLOWABLE EPA MAXIMUM WEIGHT
M= OUNTING HEIGHT &= nbsp; (= ft)	S= HAFT S= IZE O.D. (= in)	W= ALL T= HK &= nbsp; (= in)	S= TRUCT. WEIGHT &= nbsp; (= lbs)	A= NCHOR B= OLTS D= ia x Length x Rt (= in)	B= OLT CIRCLE D= iameter (= in)	L= UMINAIRE WEIGHT	7= 0 MPH w= / 1.3 Gust	8= 0 MPH w= / 1.3 Gust	9= 0 MPH &= nbsp;w/ 1.3 Gust	1= 00 MPH w= / 1.3 Gust	1= 10 MPH w= / 1.3 Gust
W= eight (= lbs)	E= PA (= ft<= span dir=3Dltr>²)	E= PA (= ft<= span dir=3Dltr>²)	E= PA (= ft<= span dir=3Dltr>²)	E= PA (= ft<= span dir=3Dltr>²)	E= PA (= ft<= span dir=3Dltr>²)
8	4	.125	22	3/4 x 24 x 4	8¼= = ±= ½	75	17.8	13.2	10.1	8.0	6.5
10	4	.125	25	3/4 x 24 x 4	8¼= = ±= ½	75	13.2	9.8	7.2	5.5	4.5
10	4	.188	35	3/4 x 24 x 4	8¼= = ±= ½	150	14.9	11.6	9.1	7.4	6.2
10	4	.250	42	3/4 x 24 x 4	8¼= = ±= ½	150	16.7	13.5	11.1	9.3	8.0
10	5	.125	30	3/4 x 24 x 4	8¼= = ±= ½	150	21.5	16.0	12.5	10.0	8.6
12	4	.125	28	3/4 x 24 x 4	8¼= = ±= ½	75	9.9	7.1	5.1	3.8	3.1
12	4	.250	45	3/4 x 24 x 4	8¼= = ±= ½	150	13.3	10.6	8.6	7.2	6.1
12	5	.125	35	3/4 x 24 x 4	8¼= = ±= ½	150	16.6	12.1	9.4	7.4	6.3
12	5	.188	50	3/4 x 24 x 4	8¼= = ±= ½	150	25.5	19.1	14.8	11.9	9.6
14	4	.125	35	3/4 x 24 x 4	8¼= = ±= ½	150	7.2	4.8	3.3	2.2	1.8
14	4	.188	45	3/4 x 24 x 4	8¼= = ±= ½	150	9.0	6.6	5.0	3.8	3.1
14	4	.250	50	3/4 x 24 x 4	8¼= = ±= ½	150	10.8	8.4	6.8	5.5	4.5
14	5	.125	40	3/4 x 24 x 4	8¼= = ±= ½	150	12.8	9.2	7.1	5.6	4.7
14	5	.188	55	3/4 x 24 x 4	8¼= = ±= ½	150	20.5	15.1	11.6	9.3	7.5
14	5	.250	70	3/4 x 24 x 4	8¼= = ±= ½	150	25.2	20.6	17.2	14.5	12.4
16	4	.125	35	3/4 x 24 x 4	8¼= = ±= ½	150	5.2	3.3	1.9	1.2	-=
16	4	.188	55	3/4 x 24 x 4	8¼= = ±= ½	150	7.3	5.3	3.8	2.6	2.0
16	4	.250	58	3/4 x 24 x 4	8¼= = ±= ½	150	9.4	7.3	5.7	4.0	3.2
16	5	.125	45	3/4 x 24 x 4	8¼= = ±= ½	150	10.0	6.9	5.2	4.7	4.0
16	5	.188	65	3/4 x 24 x 4	8¼= = ±= ½	150	16.5	11.9	9.2	7.2	5.8
16	5	.250	80	3/4 x 24 x 4	8¼= = ±= ½	150	21.3	17.4	14.5	12.2	10.0
16	6	.188	75	3/4 x 24 x 4	9¾= = ±= ½	150	26.2	19.8	15.3	12.6	10.4
18	4	.250	65	3/4 x 24 x 4	8¼= = ±= ½	150	7.0	5.1	3.6	2.8	2.1
18	5	.125	48	3/4 x 24 x 4	8¼= = ±= ½	150	7.5	5.6	4.3	3.5	2.9
18	5	.188	70	3/4 x 24 x 4	8¼= = ±= ½	150	13.3	9.4	8.0	5.5	4.5
18	5	.250	85	3/4 x 24 x 4	8¼= = ±= ½	150	17.8	14.5	12.0	10.1	8.6
18	6	.188	85	3/4 x 24 x 4	9¾= = ±= ½	150	21.8	16.4	12.6	10.0	8.1
20	4	.250	70	3/4 x 24 x 4	8¼= = ±= ½	150	5.8	3.5	2.5	1.8	1.3
20	5	.125	50	3/4 x 24 x 4	8¼= = ±= ½	150	5.9	4.2	3.1	2.4	1.9
20	5	.188	75	3/4 x 24 x 4	8¼= = ±= ½	150	11.1	7.5	5.6	4.2	3.3
20	5	.250	95	3/4 x 24 x 4	8¼= = ±= ½	150	14.8	12.0	9.9	8.3	7.0
20	6	.188	90	3/4 x 24 x 4	9¾= = ±= ½	150	18.7	13.9	10.7	8.4	6.7
22	5	.188	85	3/4 x 30 x 4	8¼= = ±= ½	150	10.4	8.3	6.8	5.6	4.7
22	5	.250	110	3/4 x 30 x 4	8¼= = ±= ½	150	12.4	9.9	8.1	6.7	5.7
24	5	.188	90	3/4 x 30 x 4	8¼= = ±= ½	150	8.4	6.6	5.3	4.3	3.6
24	5	.250	115	3/4 x 30 x 4	8¼= = ±= ½	150	10.3	8.2	6.6	5.5	4.5
25	5	.188	95	3/4 x 30 x 4	8¼= = ±= ½	150	7.5	5.9	4.7	3.8	3.1
25	5	.250	120	3/4 x 30 x 4	8¼= = ±= ½	150	9.3	7.4	6.0	4.9	4.0
25	6	.188	110	3/4 x 30 x 4	9¾= = ±= ½	150	11.5	8.4	6.2	4.7	3.6
30	6	.188	135	3/4 x 30 x 4	9¾= = ±= ½	200	6.1	4.1	2.8	1.9	1.3

POLE

SIZE (IN)

SHAPE

MATERIAL

WALL THK

LENGTH (FT)

HARDWARE

COLOR

= P

= -

= 4

= -

= RD

= -

= ALUM

= -

= 120

= -

= 20

= -

= HRDWR

= -

= DB

OPTIONS

TN =3D TENON

DTB =3D DIRECT BURIAL

LAB =3D LESS ANCHOR BOLT

CP =3D COUPLING (1/2” OR 3/4”)

CC =3D CUSTOM COLOR